Flow Monitoring System

Setting up your boxes

Follow the steps in order. Already done one? Skip to the next. Tap a step to open it.

Steps

1 Order your boxesFrom our online store
  1. Order in our online store at carwashminder.com.
  2. You'll get an email with your paid invoice and a link back to this guide.
  3. Every order ships by carrier to your business address.
To get the most out of the system, put one sensor on every chemical injection point.

Not sure how many boxes you need? Email us at info@carwashminder.com with your bays and chemical lines, and we'll help you work it out.

Got your boxes from someone else? Skip to step 2. Everything else is the same.
2 Plan your installWiFi, mounting, plumbing, chemical map

WiFi

Each box needs a strong 2.4 GHz WiFi signal at the spot where it will be mounted, not just in the office. Free WiFi signal apps can check this. See WiFi help under Questions - Issues for exactly what the box needs from your network.

Mounting

Every equipment room is different, so only basic mounting hardware is included. The best installation is drilling into available metal, or attaching to Unistrut or something similar.

  • Each box comes with 2 mounting connectors you can use or remove. Most customers remove them and put the bolts straight into thin metal.
  • Boxes can also go on a backing plate, or be zip-tied to existing framework.
  • One box per bay. Boxes are bay-specific, so don't share one box across bays.
  • Mount it right side up, so the company name on the front reads normally.

Plumbing

Best: run the chemical line up from the barrel, through the box, and on up to the injector. This keeps air out of the line.

If that isn't possible: run up to the box and then down to the injector, with one visible high point in the line so any bubbles can be seen and purged.

Chemical map

Sketch your system before you start:

  • Brand, model, tip size, and water pressure of each injector
  • Which barrel feeds each injector
  • A clear label on each barrel (for example "Bay 3 Lo-pH" or "North Lo-pH Barrel")
  • Which box sits between each barrel and injector
  • Barb numbers on each box. Barb 1 is closest to the power connection.

The numbering itself doesn't matter. Being consistent does. You'll match chemicals to barb numbers in the dashboard.

Taking care of the boxes

  • The box casing resists all the car wash chemicals we have tested except some Hi pH Boost products, which can eat the plastic over time. The flow sensors inside are not affected.
  • If concentrate spills on a box, rinse or wipe it off promptly.
  • Water poured over the box is fine, even while it's plugged in. Do not pressure wash the boxes.
  • For heavy cleaning, unplug the cable if you can but leave the metal 90-degree connector in place. Let it dry before plugging back in.
3 Create your accountSign up with the owner's email
  1. Go to carwashminder.com and click Sign Up.
  2. Use the owner's email address. It can't be changed later, and each owner email can belong to only one organization. You can add more users at any time.
  3. After you sign in, you land on your monitoring dashboard.
4 Add your boxesAT THE SITE, near the router, one box at a time

You need: a phone (or any device with WiFi) and a pen or Sharpie. Do this AT THE SITE, with all the boxes near the site's WiFi router. You'll move them to their final spots in step 5.

Do this one box at a time.

A. Get your Install Token

  1. Sign in at carwashminder.com and go to Admin → Settings → Provision Locations → Add Hardware → Add Flow Meter.
  2. The screen shows an Install Token. Write it down. You'll type it into the box in part B.
Each Install Token works for one box and lasts 30 minutes. If it runs out, come back here for a new one.

B. Connect the box

  1. Plug in one box near the site's router.
  2. On your phone, open WiFi settings and join the network FlowMeter_XXXXXX. The XXXXXX code is on the back of the box and is the box's name. Write down the box name and where it will go.
  3. Your phone may warn that this network has no internet. Choose Yes / stay connected.
  4. Open a web browser and go to 192.168.4.1.
  5. Enter your site's WiFi name and password (2.4 GHz) and press Connect to WiFi. Wait for "Connected to (your network)!"
  6. Under Device Registration, enter the Install Token you wrote down and press Register Device.
  7. The box light goes from blinking red to solid green.

C. Check it worked

  1. Put your phone back on your normal WiFi. (Your phone is kicked off the box's FlowMeter WiFi once the box has your site's WiFi.)
  2. Within a few minutes you'll get an email: "Box XXXXXX is connected." The box also shows in the dashboard.
  3. Next box: in the dashboard, click Add Another Flow Meter for a new Install Token, and repeat from part A.
Leave all the boxes plugged in near the router for at least 10 minutes on solid green so they can update.
Tip: label the boxes. Write each box's name on the front with a Sharpie (for example "Box XXXXXX", using the code from the back of the box). It makes the later steps a bit easier.

Trouble connecting? See WiFi help.

5 Install at the final spotMount, fittings, hoses, first 24 hours

Mount and power up

Mount each box at its final spot and plug it in. The light should turn green again.

Blue light at the final spot? The WiFi there is too weak. Improve coverage at that spot until the light stays green, for example with a WiFi extender, an access point, or a better router.

Fittings

  • New fittings ship with 3 wraps of Blue Monster PTFE tape (Mill-Rose 70885) already applied. Thread the fitting on and tighten about 4 full turns from first thread engagement. Do not go past 6 turns: overtightening can crack the plastic threads, and a cracked thread cannot be sealed.
  • If you see air bubbles entering the line, tighten the fitting in 1/4-turn steps, up to 6 turns total. If it still leaks, remove it, clean off all the old tape, apply 3 fresh wraps and reinstall.
  • Whenever you remove and reinstall a fitting, remove the old tape completely and apply 3 fresh wraps of Blue Monster tape clockwise around the male threads, starting at the first thread. Take care to ensure no foreign debris gets into the flow meter.
  • After installation, watch the fitting for the first few days for air bubbles entering the line or liquid around the threads.
  • These hose barb fittings are made from PVDF and use 1/4" BSPT tapered threads. We recommend replacement fittings supplied by us. Any PVDF fitting with 1/4" BSPT threads should also work.

Hoses

The barbs are tight on purpose so they seal well.

  • To install: coat the barb lightly with a slippery chemical you already use, then push the hose all the way on.
  • To remove: cut the hose, take the barb out with a 17 mm deep socket (see Optional tools below), and soak it in hot water to loosen the hose.
  • Never pull a hose off by force. It cracks the barb.

First 24 hours

  • Let it run for at least 24 hours.
  • Watch the lines for air bubbles. Air in a line affects the readings.
  • Check the fittings for bubbles, seepage, or liquid around the threads, and fix any problem right away.
  • Make sure the injectors run normally.
Optional tools
6 Follow your Setup GuideIn the dashboard, under Admin → Settings

Sign in at carwashminder.com and click Admin in the top menu, then Settings. The Setup Guide lists every step in order, with a check mark as each one is done.

Don't see the steps? Switch Setup guide to On at the top of the page.

Day 1

  • Add your boxes and put each one at its location
  • Set your time zone and units
  • Tell us which bay each box is in and which chemical is on each line
  • Check that every chemical is showing usage

After a few days

  • Add your chemicals and their prices
  • Create a barrel for each chemical line
  • Set the order your chemicals are shown in
  • Set up your wash packages
Once your boxes are online, we can see them and help you remotely with any of these steps. Email us at info@carwashminder.com.
! GotchasShortcuts other installers have taken, and the trouble they caused
Connecting the box at its final spot instead of close to the routerThe WiFi is often weak out there, so the connection fails or keeps dropping. This is the most common setup problem.Instead: Connect every box close to the router (step 4). Once it's green, move it to its final spot and check that it turns green again.
Unplugging as soon as the light turns greenThe box is still updating itself. If you cut it off, it can take a while to work properly at a busy site.Instead: Leave it plugged in on solid green for 10 minutes.
Forcing a hose onto a dry barbA cracked barb.Instead: Coat the barb lightly with a slippery chemical you already use, then push the hose all the way on.
Fittings too loose or too tightToo loose lets air into the line and throws off the readings. Too tight cracks the plastic threads.Instead: 15-18 in-lb, usually about 4 full turns. Never more than 18 in-lb or 4.5 turns (step 5).
Pulling a hose off by forceA cracked barb.Instead: Cut the hose, take the barb out with a 17 mm deep socket, and soak it in hot water to loosen the hose.
Leaving spilled chemical on the boxSome Hi pH Boost products eat the plastic. One customer lost a box this way.Instead: Rinse or wipe spills off right away. Water is fine, even while it's plugged in.
? Questions - IssuesWiFi help, WiFi reset, hotspot setup, and more
WiFi help: my box won't connect

You can forward this section to your IT person or internet provider.

What the box needs from your WiFi
  • 2.4 GHz. 5 GHz is not supported. A router that uses one name for both 2.4 and 5 GHz is fine.
  • WPA2-Personal, or WPA2/WPA3 mixed. Not WPA3-only. Not a network that asks for a username (Enterprise).
  • No sign-in page. Guest networks that show a web page to accept terms or log in won't work.
  • MAC filtering off, or the box's address allowed.
  • Automatic IP (DHCP) on, and normal internet access (HTTPS) allowed out.
  • A good signal where the box is mounted, not just in the office.
What the light means
LightMeaning
Two quick red flashes, repeatingSetup mode. Join FlowMeter_XXXXXX from your phone.
Solid greenConnected. All good.
Solid blueCan't connect to its saved WiFi, still trying.
Was it green here before? Most likely a weak signal. Improve the WiFi at that spot.
Just moved, or new router or password? Do a WiFi reset and set the box up again.
Two quick blue flashes, repeatingSetup mode, but the box can't find any WiFi networks at all. Move the box closer to the router, or check that 2.4 GHz is on.
Solid redConnecting. Normal for a few seconds at power-up.
Error messages on the setup page

These show on the box's page at 192.168.4.1 after you press Connect to WiFi.

ErrorMeaningWhat to do
201Network not foundCheck the network name. Make sure the router has 2.4 GHz turned on.
200, 212Signal too weakMove the box closer to the router.
15, 202, 204Password problemRe-type the password. If it's right, set the router to WPA2 or WPA2/WPA3 mixed.
5Router is fullDisconnect some devices and try again.
203Router refused the boxCheck MAC filtering.
8Couldn't finish connectingUsually a weak signal, a WPA3-only router, or a guest network with a sign-in page. Usually not the password.
Quick checks

Is my network 2.4 GHz? Is it WPA3? Check on a laptop that's on the same WiFi.

  • Windows: click the WiFi network, then Properties. Look at "Network band" and "Security type".
  • Mac: hold Option and click the WiFi icon. Look at "Channel" (2.4 GHz is channel 1 to 11) and "Security".

Phone hotspot test. Set the box up on a phone hotspot, iPhone or Android (how). If that works, the box is fine and the problem is in the router settings.

Install Token expired. If getting onto WiFi took a long time, the token may have run out. Go back to Add Flow Meter for a new one.

How do I reset a box's WiFi? (new router or password)

New router or new password? There are two ways to clear a box's WiFi. Either way the box stays on your account, so you won't need a new Install Token.

Method 1: unplug and plug in (no tools)

  1. Leave the box powered for 45 seconds.
  2. Unplug it for about 2 seconds, plug it back in, and wait 5 seconds. Do this 3 times. The light turns solid red and stays red.
  3. Wait 60 seconds without touching it. The light turns off.
  4. Within 30 seconds of the light turning off, do the same unplug / plug in / wait 5 seconds 3 times. Leave it plugged in.
  5. After about 30 seconds the light gives a few quick red blinks and the box goes back into setup mode.
  6. Set it up again from step 4.
If the light turns green during step 2, the count didn't take. Start again with a slightly longer unplug.

Method 2: the button inside the box

  1. With the box plugged in, pop the cover off with a thin flathead screwdriver.
  2. About 2 inches to the left of the power connector there are two buttons. Use the upper one, the one in line with the light and the power connector.
  3. Push and hold it for 15 seconds, then let go. The light doesn't change while you hold it, so count.
  4. About a second after you let go, the box restarts in setup mode (two quick red flashes).
  5. Put the cover back on and set the box up again from step 4.
Let go before 30 seconds. Holding for 30 seconds also takes the box off your account, and you'd need a new Install Token. The lower button only restarts the box.
Can I set up my boxes on my phone's hotspot (off site, or when my router is giving me trouble)?

Yes. A phone hotspot (or any other hotspot) works like a router for the box. It's a good way to set up a box before you're at the site, or when your router is giving you trouble.

  1. Make your hotspot match your site's WiFi: give it the exact same network name and password as your site's WiFi (same capital letters, spaces and symbols).
  2. Turn on your hotspot, set to 2.4 GHz:
    • iPhone: Settings → Personal Hotspot. Turn on Maximize Compatibility.
    • Android: Settings → Network & internet (Samsung: Connections) → Hotspot & tethering → WiFi hotspot. Set the band to 2.4 GHz (on some phones it's a switch called Extend compatibility). If there's a security setting, choose WPA2-Personal, not WPA3.
  3. You need a second device for the setup (the phone running the hotspot can't also join the box's WiFi). Set each box up as in step 4, choosing your hotspot (it shows with your site's network name).
  4. The light turns solid green and you get the "Box XXXXXX is connected" email. Leave it on for 10 minutes so it can update.
At the site, just plug it in. The box saved your site's network name and password during setup, so it connects to your site's WiFi by itself. Turn the hotspot off first so the box joins your router, not your phone.
Used a different name or password on the hotspot? Then the box only knows the hotspot. At the site, do a WiFi reset, join FlowMeter_XXXXXX, and enter your site's WiFi. You don't need a new Install Token; the box stays on your account.

Works on the hotspot but not on your router? Then the box is fine and the problem is in the router settings. See WiFi help.

The light is green, but I can't see any chemicals in the dashboard.

Green means the box is connected to the internet, and help is an email away.

  • Go through the Setup Guide (step 6), and pay particular attention to your bays: each box needs to be in the right bay, with the chemical filled in on each line.
  • Check Chronological Usage. In the dashboard, open Chronological Usage and see if anything is showing up there.
  • Still nothing? Email info@carwashminder.com with the approximate date and time you added the box, and we can help.
I connected my boxes to WiFi before I created an account. What now?

Create your account (step 3), then email us at info@carwashminder.com with:

  • the approximate date and time you added the boxes
  • the exact location name you want them assigned to

We'll add the boxes to your account. You don't need to set them up again.